So now I just need to figure out how to get it to work outside of my local network. There are some limitations though - currently not all bluetooth mice are supported. Additionally I have the port forwarding setup for port 7 and the ip of that secondary card. Jump Desktop for iOS has the ability to connect to a physical mouse on a stock iOS device. It has a setting in the app to enable if your using it through a VPN, which I enabled but it didnt help.Īlso, for anyone else ever looking for this info, I also had the secondary nic setup in the router with mac/ip binding and a reserved ip address. Since the tv wasnt picking up a signal I thought the wake on lan wasnt functioning. When I turn my wifi off and turn on the router VPN the wol no longer works. But when it booted up it displayed on the built in laptop display (which is closed and tucked away in my media stand) instead of the tv screen. I decided to look up the mac and ip of the secondary nic and set it up in the wol app and BAM, it turns the computer on instantly.but only when being used locally on the same network. SOOOO, I was trying to setup the WOL using that nic and it wasnt working. In this guide, well show you the steps to enable Wake on LAN on your computer and send a magic packet over the network to turn on the device remotely. This is the mac and ip the router uses for the computer, as a matter of fact, eventhough two ports are plugged in on the router it shows up as 1 with the mac/ip of the primary nic. So the primary nic has a mac and ip which is also used as the mac/ip for the bonded combination of the two. Overall right now this is a 100% fresh install of OPNsense with the os-wol plugin installed and all updates ran.Well, I have it half working! SOOOO, I actually have two nic's on the computer and they are bonded together and the two cables go to two ports are the router where it uses link aggregation to combine them. I'm open to suggestions, also if more information is needed just let me know. I then hooked my switch up to the router and hooked my PC into the switch and tried sending another WOL packet from my phone and it came through without issue on my PC, verified with WireShark. I had a spare Netgear Router (R6330) and plugged my PC directly into it and connected my phone to the WiFi and sent a WOL Packet from it and it showed up on WireShark. "arp -S 192.168.10.254 ff:ff:ff:ff:ff:ff" and then sent a WOL from OPNsense and still nothing on WireShark but OPNsense gave me an "Error(1)" when I tried to send a WOL packet from the GUI.įinally I wanted to ensure that my ethernet port on my mobo wasn't the issue or anything else. In order to wake a computer from sleep mode for a remote desktop session, youll need to have the ARP (Address Resolution Protocol) offload and the NS. I found this thread: and added a static arp for using I even tried using the onboard realtek nic running directly to my PC as well. I would expect Jump to see that I had an open session and opon the mac waking up to reconnect and let me continue my RDP session. Install WOL on client machines to enable remote wakeups, and on every machine you want to use for sending the wakeup. I've tried taking the switch out and running my LAN port directly to my PC. I have to actually go to jump and click disconnect and then go to Window/My computers and re-connect. I've tried swapping my LAN and WAN ports on my intel card. Wake-On-Lan only works if you fulfil the following preconditions: The target computers motherboard and Network Interface Controller has to support Wake-on-LAN. Tried using shell and typing "sudo wake igb0/igb1/re0 04:d4:c4:XX:XX:XX" all separate respectively as I was moving my PC across the different ports, I also put X's in this post to "protect?" my MAC but used my actual MAC when running the commands. Typed my MAC, ensured that it is entered correctly. I've used Wireshark to verify that no WOL packet is being sent. Whether it was developed for editing or not, its been working great. 1 gig up and down, with a 1ms response time. The LAN port then feeds into a TP Link switch (TL-SG1008P) and my PC is then ran with a standard cat 6 cable. But our IT is really on the ball with this one. I ensured Magic Packet is enabled in Windows and ensured it is also enabled on BIOS. My Desktop Mobo: ROG MAXIMUS XI HERO (WI-FI) 90MB0XR0-M0EAY0 My OPNsense Box: HP t730 Thin Client PC with an I350-T4V2 running OPNsense 22.1.10-amd64 I installed the WOL plugin (os-wol) version 2.4_1 Hello all, recently switched over from pfSense and have kinda ran into a wall.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |